View source for Wanhao Duplicator 4 Using Simplfy 3D


=Specifications=

Maximum Print Size: 22.5 x 14.5 x 15 cm

Layer Thickness: 100 microns in ABS, PLA and PVA

==== Settings ====

*Device Settings: (Typically 200- 215°C for the extruder and 70°C for the platform) 

*Extrusion Speeds 
*Infill (Lower this for faster prints. Raise it for stronger prints.)
*Model Properties 
*Multi-Material Printing: (One can add Purge Walls to help eliminate loose filament from attaching to the piece)
*Raft: (Usually a good idea to keep on)
*Supports and Bridging (Used when parts have an overhang so that the printer has a surface to print on)
*Right Extruder
*Left Extruder

=Using Simplfy 3D=
'''Simplify 3D is only available on __Space.URI's two dell laptops as well as three desk tops'''

# Open Simplify 3D 
 *If there is an existing file on the bed click remove or delete so that you can begin your project
<ol start="2">
<li>Click the "import" button to import your .stl or .obj file</li>
<li>Select your file and then click open. Your object should then appear on the bed</li>
<li>The Select "edit process settings," a new window should open. Confirm that the selected profile is Wanhao Duplicator 4/ 4s dual. </li>
</ol>
 *This new window will allow you to alter various settings. Ex.) Infill, Percentage, Skirt/ Brim, Generating Support, etc. You an also edit the temperature of the nozzle and bed. Recommended nozzle temp. is 210 degrees, bed temp. is 60. Once satisfied hit okay.

 * If your printer is not found on the list, follow these steps: 
 1. Under the "help" tab select "configuration assistant," and a new window should open
 2. Under the "select printer" tab locate your desired printer (in this case: Wanhao Duplicator 4/4x dual)
 3. Click next and then finish
 4. Eddit the process settings to the following:
   *Change auto configuration for the material from ABS to PLA
   *Change the temperature for the Right and Left extruder to 210 degrees

<ol start="5">
<li>Run through all the tabs and edit the FFF file to your liking</li>
<li> When you are done editing your FFF file hit okay</li>
<li> Double click on your object to bring up a new menu where you can change the position, scaling, and rotation of your object. Once satisfied select done.</li>
<li> When you are ready to print select "Prepare to Print!" Located on the bottom left hand corner. This will bring you to a preview mode where you can watch your model virtually print.</li>
<li> When ready to export save, select save tool paths to disk</li>
<li> Save your file</li>
</ol>
You are now ready to print your file on the duplicator 4!

=== Printing a .x3g file ===

# Turn on Wanhao 4 with power switch located on the back of the printer.
# Insert a micro SD chip containing a .x3g file into the bottom right port on the Wanhao 4.
# Locate “Print from SD” on the Wanhao’s screen and select OK.
# Use the arrows to select the desired file then press OK.
# The printer will begin printing.
Note: Remember to apply glue or blue tape, purple Elmer's is provided in the bins near the 3D printers
          To cancel a job, push OK, locate and select “Cancel Print” and select yes.
Note: It is important that object lay flat on the bed to get a good foundation and so that the printer is able to accurately print the object.

===Loading filaments===

# Power on the Wanhao Duplicator 4
# Select "Utilities-" "Filament Loading-" "Load Left/Right"
# Wait for the Duplicator 4 to preheat
# Place spool on spool holder located behind the printer. The spool should release on the side of the printer.
# Pull out the black tube from the top of the extruder 
# Feed the filament through the back end of the tube until it comes out.
# After being preheated, push down on the black lever near the extruder and begin feeding the filament through the extruder hole
# Push down the filament until the machine begins self feeding

<!--=Selecting the Profile=

#Under "auto configure" choose the correct material
#Click prepare to print
#Check to ensure your model is ready to print
#Choose "save tool paths to disk"
#When using the Wanhao save your model to a SD card-->